Clarice Lang
17 hours ago15
4
Sep 4
Dear Early Bird Backers, In case you receive Nybble early, please find the following animations as basic assembling instructions. Some of them were created earlier and are slightly different from the
Liubomyr
6 days ago36
5
Chris Rogers
Dec 3126
4
Search
Assembly and setup
Discuss the assembling and solve the puzzle together!
an hour ago
Hi, I've recently started building my nybble but I'm stuck on trying to get the servos to push in completely when assembling the body. The belly doesn't seem to go in far enough for the servos to lock
Nov 25
Hello, is it possible that i have somehow flipped left/right position on sensor ? When i lean nybble to left it is not trying to compensate but moving even more left. Same for right. Front and back le
Sep 15
I've fixed the previous issue where I was not correctly using the serial console, but I'm still having issues with servo calibration. I ran the testServo app - Only servo 0 did anything - even though
Sep 12
The piece I have that connects the two shoulders (https://youtu.be/B8N2KAf8p28?t=34) have two holes on either side of the wood, not two and three like in the part photo in the assembly instructions (s
Aug 24
Hey Guys, I'm going to make a better diagram showing the physical servo connections on NyBoard. Currently the joint map looks like: Because Nybble doesn't have shoulder roll DoF, it's hard to mark t
Nov 28
With writeinstinct.ino sketch loaded I calibrated joints, updated instincts, and calibrated the MPU6050 with no problems. When entering commands into the serial monitor all positions work and run grea
Nov 20
I can't make heads or tails of attaching the wiring for the head or tail (or legs). I see lots of diagrams on the help forum that I can't understand. Is there a photo or diagram that says, "these pr
Oct 9
The assembling instruction suggests keeping V_S switch connected to V+ (the out of the box option) if one uses NyBoard_V0_2 with plastic servos. But surprisingly it doesn't work to me. A calibration p
Sep 15
When I try to run the WriteInstinct.ino for first time setup, it only prompts me to reset the settings. I dont get any further prompts and cannot enter `c` to start calibration. The instructions are a
Sep 8
I am trying to put the Nyboard onto the body and cannot find directions how to install it, specifically, which screws to use and from which direction to screw them in (from the top or from the bottom)
Jul 21
In the Assembling Nybble#2: Battery Holder video on youtube: https://www.youtube.com/watch?v=pReSF-qKlKA There is a switch shown. That switch doesn't seem to be part of the kit as far as I can tell.
Jul 9
The full process of calibration in WriteInstinct.ino is: 1. You don't know where the servos are pointing at before calibration. So you don't attach the legs. 2. Upload skills, which include one "cali
Nov 26
I'm building the cat with my son as a father/son project and we're so close to finishing, but can't figure out the cable connections. I can't make heads or tails of attaching the wiring for the head
Nov 6
Hello, i have an issue with calibration. I have new kit with v2 board, original servos. Batteries are ok, measured and fine but i did try external laboratory power supply as well but without luck. Fi
Sep 17
I am trying to add program the kitten for the first time. I have the FTDI board connected to the kitten v0_2 board and the usb to my Mac OSX. When I make the physical connection the board makes a very
Sep 15
I've discovered that if you solder headers onto D8/D9/D10/5v/GND on the Nyboard for future ' sonar' sensor use, the headers interfere with part of the body juuust enough that the mounting holes no lon
Aug 8
hi ive got as far as the setup part and im getting a i2cdev missing error when trying to setup calibration. i have tryed looking on the net but there is alot of different i2cdev files and i dont know